![kel tec p 11 reliability kel tec p 11 reliability](https://i.ytimg.com/vi/Yb043Tz_thA/maxresdefault.jpg)
Time from Immersion to Last Round: 1 Minute & 25 Seconds.Īmmunition used: Winchester Factory White-Box 90 Grain.Īn old, Rotary-Dial Stop-Watch was used for all of the times.Ĭcm2361 wrote:Thank you for experimenting. Time from Immersion to first Round: 1 Minute & 10 Seconds. Results: The gun properly fired all 6 rounds without incident.
#KEL TEC P 11 RELIABILITY FULL#
Quickly reassembled the pistol & inserted a full magazine of 6 rounds and fired all rounds. Removed slide and shook it for about 10 seconds (did not wipe off the slide). Removed Barrel & Recoil Spring, put the Slide into the Coffee Can of Kerosene for 5 minutes. Applied open flame to the slide (including both ends of the Firing Pin Channel) with a Bic-type lighter. Removed the Slide, shook it for 10 seconds and wiped it with a cloth for about 1 minute. Removed Barrel & Recoil Spring from Slide and immersed the Slide in a Coffee Can of Kerosene for 6 minutes.
![kel tec p 11 reliability kel tec p 11 reliability](http://blog.gunlink.info/wp-content/uploads/2014/01/p11frameRemoved.jpg)
It's Monday, and here are your test results: But to insure that I can bet my life on it, I know its weaknesses and plan accordingly. So, again, I use my P3AT and carry it every day. If I really think that I am going into a high-risk area, I remove the plastic bag, until I get back to my farm. The bullets blow out the front, and the empty brass blows out the side. I even practice drawing the pistol and firing it while still in the plastic bag. It also protects the finish, somewhat, from perspiration in the hot months. It may look really stupid, but it keeps dirt, lint, sand, & sawdust out of the Firing Pin Channel. Now, I personally carry my P3AT inside of a closed Plastic Sandwich Bag, then in a soft holster, then in my pocket. You may want to consider regularly removing the Extractor Screw, Extractor, Firing Pin, and Spring to clean & inspect it for lint (you have to use a "star" Allen Wrench). This "should" tend to float out particles, but you cannot be really certain without physically checking. You can remove the slide assembly and slush it back & forth in a bucket of kerosene or Poly-Dunk. If you are going to use the gun for Critical Use, test-fire it regularly, directly from the condition that you normally carry it.
#KEL TEC P 11 RELIABILITY HOW TO#
He also tells how to remove the Extractor, Firing Pin, & Spring. In the following YouTube Video (in the comments section), a gunsmith stated that he has seen Kel-Tec pistols malfunction, because of simple pocket-lint in the firing pin channel. I am not the only person who has seen this problem. I sent the pistol to Kel-Tec, they took care of the problem, and I had the gun back in about 5 weeks. At the time, I thought that it may have been staked in, but I have learned that it was just held in with Lock-Tite. I attempted to remove the extractor, firing pin, & spring, but was unable to. Upon inspection, I could see fine sawdust that had gotten into my pocket and migrated into the Firing Pin Channel. I was met with light firing pin strikes on each round, and about 50% Fail-to-Fire.ĭuring the time that I had kept the pistol with me, I had been chain-sawing firewood. You cannot re-strike the primer with the Kel-Tec, so I had to rack the slide and try again. I pulled the pistol from my pocket (normal carry configuration), drew down on the target, pulled the trigger, and "CLICK". Every couple of months, I like to take it down to the range just to re-familiarize.
![kel tec p 11 reliability kel tec p 11 reliability](https://images.guns.com/prod/fOrz6hvERIo6oWisMvPU8hILfipvjf2pWPMTx6gR.jpeg)
I had been receiving threats that an individual was going to come after me with a firearm, so I kept my P3AT constantly in my pocket. I had personal first-hand experience with this. The problem is that you cannot see when this occurs and could cause a problem. Making things worse, there is a "notch" cut in the back of the firing pin, which gives dirt/lint/sand a natural path into the Firing Pin Channel, which can clog it. This makes this location vulnerable to having foreign material get into the firing pin channel. They are not covered by the hammer or by the back of the slide. The P-32 and P3AT both have firing pins that are exposed in the "carry" configuration. This is not meant to "knock" the pistols, but if there is a potential reliability problem, the owner is better-off being aware, so that he can take appropriate actions. Since Chris just acquired a Kel-Tec P-32, I want to address a weakness in the design of it and the P3AT.